#ifndef WLED_CONST_H
#define WLED_CONST_H
/*
* Readability defines and their associated numerical values + compile-time constants
*/
#define GRADIENT_PALETTE_COUNT 58
//Defaults
#define DEFAULT_CLIENT_SSID "Your_Network"
#define DEFAULT_AP_SSID "WLED-AP"
#define DEFAULT_AP_PASS "wled1234"
#define DEFAULT_OTA_PASS "wledota"
#define DEFAULT_MDNS_NAME "x"
//increase if you need more
#ifndef WLED_MAX_USERMODS
#ifdef ESP8266
#define WLED_MAX_USERMODS 4
#else
#define WLED_MAX_USERMODS 6
#endif
#endif
#ifndef WLED_MAX_BUSSES
#ifdef ESP8266
#define WLED_MAX_BUSSES 3
#define WLED_MIN_VIRTUAL_BUSSES 2
#else
#if defined(CONFIG_IDF_TARGET_ESP32C3) // 2 RMT, 6 LEDC, only has 1 I2S but NPB does not support it ATM
#define WLED_MAX_BUSSES 3 // will allow 2 digital & 1 analog (or the other way around)
#define WLED_MIN_VIRTUAL_BUSSES 3
#elif defined(CONFIG_IDF_TARGET_ESP32S2) // 4 RMT, 8 LEDC, only has 1 I2S bus, supported in NPB
#if defined(USERMOD_AUDIOREACTIVE) // requested by @softhack007 https://github.com/blazoncek/WLED/issues/33
#define WLED_MAX_BUSSES 6 // will allow 4 digital & 2 analog
#define WLED_MIN_VIRTUAL_BUSSES 4
#else
#define WLED_MAX_BUSSES 7 // will allow 5 digital & 2 analog
#define WLED_MIN_VIRTUAL_BUSSES 3
#endif
#elif defined(CONFIG_IDF_TARGET_ESP32S3) // 4 RMT, 8 LEDC, has 2 I2S but NPB does not support them ATM
#define WLED_MAX_BUSSES 6 // will allow 4 digital & 2 analog
#define WLED_MIN_VIRTUAL_BUSSES 4
#else
#if defined(USERMOD_AUDIOREACTIVE) // requested by @softhack007 https://github.com/blazoncek/WLED/issues/33
#define WLED_MAX_BUSSES 8
#define WLED_MIN_VIRTUAL_BUSSES 2
#else
#define WLED_MAX_BUSSES 10
#define WLED_MIN_VIRTUAL_BUSSES 0
#endif
#endif
#endif
#else
#ifdef ESP8266
#if WLED_MAX_BUSES > 5
#error Maximum number of buses is 5.
#endif
#define WLED_MIN_VIRTUAL_BUSSES (5-WLED_MAX_BUSSES)
#else
#if WLED_MAX_BUSES > 10
#error Maximum number of buses is 10.
#endif
#define WLED_MIN_VIRTUAL_BUSSES (10-WLED_MAX_BUSSES)
#endif
#endif
#ifndef WLED_MAX_BUTTONS
#ifdef ESP8266
#define WLED_MAX_BUTTONS 2
#else
#define WLED_MAX_BUTTONS 4
#endif
#endif
#ifdef ESP8266
#define WLED_MAX_COLOR_ORDER_MAPPINGS 5
#else
#define WLED_MAX_COLOR_ORDER_MAPPINGS 10
#endif
#if defined(WLED_MAX_LEDMAPS) && (WLED_MAX_LEDMAPS > 32 || WLED_MAX_LEDMAPS < 10)
#undef WLED_MAX_LEDMAPS
#endif
#ifndef WLED_MAX_LEDMAPS
#ifdef ESP8266
#define WLED_MAX_LEDMAPS 10
#else
#define WLED_MAX_LEDMAPS 16
#endif
#endif
#ifndef WLED_MAX_SEGNAME_LEN
#ifdef ESP8266
#define WLED_MAX_SEGNAME_LEN 32
#else
#define WLED_MAX_SEGNAME_LEN 64
#endif
#else
#if WLED_MAX_SEGNAME_LEN<32
#undef WLED_MAX_SEGNAME_LEN
#define WLED_MAX_SEGNAME_LEN 32
#else
#warning WLED UI does not support modified maximum segment name length!
#endif
#endif
//Usermod IDs
#define USERMOD_ID_RESERVED 0 //Unused. Might indicate no usermod present
#define USERMOD_ID_UNSPECIFIED 1 //Default value for a general user mod that does not specify a custom ID
#define USERMOD_ID_EXAMPLE 2 //Usermod "usermod_v2_example.h"
#define USERMOD_ID_TEMPERATURE 3 //Usermod "usermod_temperature.h"
#define USERMOD_ID_FIXNETSERVICES 4 //Usermod "usermod_Fix_unreachable_netservices.h"
#define USERMOD_ID_PIRSWITCH 5 //Usermod "usermod_PIR_sensor_switch.h"
#define USERMOD_ID_IMU 6 //Usermod "usermod_mpu6050_imu.h"
#define USERMOD_ID_FOUR_LINE_DISP 7 //Usermod "usermod_v2_four_line_display.h
#define USERMOD_ID_ROTARY_ENC_UI 8 //Usermod "usermod_v2_rotary_encoder_ui.h"
#define USERMOD_ID_AUTO_SAVE 9 //Usermod "usermod_v2_auto_save.h"
#define USERMOD_ID_DHT 10 //Usermod "usermod_dht.h"
#define USERMOD_ID_MODE_SORT 11 //Usermod "usermod_v2_mode_sort.h"
#define USERMOD_ID_VL53L0X 12 //Usermod "usermod_vl53l0x_gestures.h"
#define USERMOD_ID_MULTI_RELAY 13 //Usermod "usermod_multi_relay.h"
#define USERMOD_ID_ANIMATED_STAIRCASE 14 //Usermod "Animated_Staircase.h"
#define USERMOD_ID_RTC 15 //Usermod "usermod_rtc.h"
#define USERMOD_ID_ELEKSTUBE_IPS 16 //Usermod "usermod_elekstube_ips.h"
#define USERMOD_ID_SN_PHOTORESISTOR 17 //Usermod "usermod_sn_photoresistor.h"
#define USERMOD_ID_BATTERY 18 //Usermod "usermod_v2_battery.h"
#define USERMOD_ID_PWM_FAN 19 //Usermod "usermod_PWM_fan.h"
#define USERMOD_ID_BH1750 20 //Usermod "usermod_bh1750.h"
#define USERMOD_ID_SEVEN_SEGMENT_DISPLAY 21 //Usermod "usermod_v2_seven_segment_display.h"
#define USERMOD_RGB_ROTARY_ENCODER 22 //Usermod "rgb-rotary-encoder.h"
#define USERMOD_ID_QUINLED_AN_PENTA 23 //Usermod "quinled-an-penta.h"
#define USERMOD_ID_SSDR 24 //Usermod "usermod_v2_seven_segment_display_reloaded.h"
#define USERMOD_ID_CRONIXIE 25 //Usermod "usermod_cronixie.h"
#define USERMOD_ID_WIZLIGHTS 26 //Usermod "wizlights.h"
#define USERMOD_ID_WORDCLOCK 27 //Usermod "usermod_v2_word_clock.h"
#define USERMOD_ID_MY9291 28 //Usermod "usermod_MY9291.h"
#define USERMOD_ID_SI7021_MQTT_HA 29 //Usermod "usermod_si7021_mqtt_ha.h"
#define USERMOD_ID_BME280 30 //Usermod "usermod_bme280.h
#define USERMOD_ID_SMARTNEST 31 //Usermod "usermod_smartnest.h"
#define USERMOD_ID_AUDIOREACTIVE 32 //Usermod "audioreactive.h"
#define USERMOD_ID_ANALOG_CLOCK 33 //Usermod "Analog_Clock.h"
#define USERMOD_ID_PING_PONG_CLOCK 34 //Usermod "usermod_v2_ping_pong_clock.h"
#define USERMOD_ID_ADS1115 35 //Usermod "usermod_ads1115.h"
#define USERMOD_ID_BOBLIGHT 36 //Usermod "boblight.h"
#define USERMOD_ID_SD_CARD 37 //Usermod "usermod_sd_card.h"
#define USERMOD_ID_PWM_OUTPUTS 38 //Usermod "usermod_pwm_outputs.h
#define USERMOD_ID_SHT 39 //Usermod "usermod_sht.h
#define USERMOD_ID_KLIPPER 40 //Usermod Klipper percentage
#define USERMOD_ID_WIREGUARD 41 //Usermod "wireguard.h"
#define USERMOD_ID_INTERNAL_TEMPERATURE 42 //Usermod "usermod_internal_temperature.h"
#define USERMOD_ID_LDR_DUSK_DAWN 43 //Usermod "usermod_LDR_Dusk_Dawn_v2.h"
#define USERMOD_ID_STAIRWAY_WIPE 44 //Usermod "stairway-wipe-usermod-v2.h"
//Access point behavior
#define AP_BEHAVIOR_BOOT_NO_CONN 0 //Open AP when no connection after boot
#define AP_BEHAVIOR_NO_CONN 1 //Open when no connection (either after boot or if connection is lost)
#define AP_BEHAVIOR_ALWAYS 2 //Always open
#define AP_BEHAVIOR_BUTTON_ONLY 3 //Only when button pressed for 6 sec
//Notifier callMode
#define CALL_MODE_INIT 0 //no updates on init, can be used to disable updates
#define CALL_MODE_DIRECT_CHANGE 1
#define CALL_MODE_BUTTON 2 //default button actions applied to selected segments
#define CALL_MODE_NOTIFICATION 3
#define CALL_MODE_NIGHTLIGHT 4
#define CALL_MODE_NO_NOTIFY 5
#define CALL_MODE_FX_CHANGED 6 //no longer used
#define CALL_MODE_HUE 7
#define CALL_MODE_PRESET_CYCLE 8 //no longer used
#define CALL_MODE_BLYNK 9 //no longer used
#define CALL_MODE_ALEXA 10
#define CALL_MODE_WS_SEND 11 //special call mode, not for notifier, updates websocket only
#define CALL_MODE_BUTTON_PRESET 12 //button/IR JSON preset/macro
//RGB to RGBW conversion mode
#define RGBW_MODE_MANUAL_ONLY 0 // No automatic white channel calculation. Manual white channel slider
#define RGBW_MODE_AUTO_BRIGHTER 1 // New algorithm. Adds as much white as the darkest RGBW channel
#define RGBW_MODE_AUTO_ACCURATE 2 // New algorithm. Adds as much white as the darkest RGBW channel and subtracts this amount from each RGB channel
#define RGBW_MODE_DUAL 3 // Manual slider + auto calculation. Automatically calculates only if manual slider is set to off (0)
#define RGBW_MODE_MAX 4 // Sets white to the value of the brightest RGB channel (good for white-only LEDs without any RGB)
//#define RGBW_MODE_LEGACY 4 // Old floating algorithm. Too slow for realtime and palette support (unused)
#define AW_GLOBAL_DISABLED 255 // Global auto white mode override disabled. Per-bus setting is used
//realtime modes
#define REALTIME_MODE_INACTIVE 0
#define REALTIME_MODE_GENERIC 1
#define REALTIME_MODE_UDP 2
#define REALTIME_MODE_HYPERION 3
#define REALTIME_MODE_E131 4
#define REALTIME_MODE_ADALIGHT 5
#define REALTIME_MODE_ARTNET 6
#define REALTIME_MODE_TPM2NET 7
#define REALTIME_MODE_DDP 8
//realtime override modes
#define REALTIME_OVERRIDE_NONE 0
#define REALTIME_OVERRIDE_ONCE 1
#define REALTIME_OVERRIDE_ALWAYS 2
//E1.31 DMX modes
#define DMX_MODE_DISABLED 0 //not used
#define DMX_MODE_SINGLE_RGB 1 //all LEDs same RGB color (3 channels)
#define DMX_MODE_SINGLE_DRGB 2 //all LEDs same RGB color and master dimmer (4 channels)
#define DMX_MODE_EFFECT 3 //trigger standalone effects of WLED (15 channels)
#define DMX_MODE_EFFECT_W 7 //trigger standalone effects of WLED (18 channels)
#define DMX_MODE_MULTIPLE_RGB 4 //every LED is addressed with its own RGB (ledCount * 3 channels)
#define DMX_MODE_MULTIPLE_DRGB 5 //every LED is addressed with its own RGB and share a master dimmer (ledCount * 3 + 1 channels)
#define DMX_MODE_MULTIPLE_RGBW 6 //every LED is addressed with its own RGBW (ledCount * 4 channels)
#define DMX_MODE_EFFECT_SEGMENT 8 //trigger standalone effects of WLED (15 channels per segment)
#define DMX_MODE_EFFECT_SEGMENT_W 9 //trigger standalone effects of WLED (18 channels per segment)
#define DMX_MODE_PRESET 10 //apply presets (1 channel)
//Light capability byte (unused) 0bRCCCTTTT
//bits 0/1/2/3: specifies a type of LED driver. A single "driver" may have different chip models but must have the same protocol/behavior
//bits 4/5/6: specifies the class of LED driver - 0b000 (dec. 0-15) unconfigured/reserved
// - 0b001 (dec. 16-31) digital (data pin only)
// - 0b010 (dec. 32-47) analog (PWM)
// - 0b011 (dec. 48-63) digital (data + clock / SPI)
// - 0b100 (dec. 64-79) unused/reserved
// - 0b101 (dec. 80-95) virtual network busses
// - 0b110 (dec. 96-111) unused/reserved
// - 0b111 (dec. 112-127) unused/reserved
//bit 7 is reserved and set to 0
#define TYPE_NONE 0 //light is not configured
#define TYPE_RESERVED 1 //unused. Might indicate a "virtual" light
//Digital types (data pin only) (16-31)
#define TYPE_WS2812_1CH 18 //white-only chips (1 channel per IC) (unused)
#define TYPE_WS2812_1CH_X3 19 //white-only chips (3 channels per IC)
#define TYPE_WS2812_2CH_X3 20 //CCT chips (1st IC controls WW + CW of 1st zone and CW of 2nd zone, 2nd IC controls WW of 2nd zone and WW + CW of 3rd zone)
#define TYPE_WS2812_WWA 21 //amber + warm + cold white
#define TYPE_WS2812_RGB 22
#define TYPE_GS8608 23 //same driver as WS2812, but will require signal 2x per second (else displays test pattern)
#define TYPE_WS2811_400KHZ 24 //half-speed WS2812 protocol, used by very old WS2811 units
#define TYPE_TM1829 25
#define TYPE_UCS8903 26
#define TYPE_UCS8904 29
#define TYPE_SK6812_RGBW 30
#define TYPE_TM1814 31
//"Analog" types (PWM) (32-47)
#define TYPE_ONOFF 40 //binary output (relays etc.)
#define TYPE_ANALOG_1CH 41 //single channel PWM. Uses value of brightest RGBW channel
#define TYPE_ANALOG_2CH 42 //analog WW + CW
#define TYPE_ANALOG_3CH 43 //analog RGB
#define TYPE_ANALOG_4CH 44 //analog RGBW
#define TYPE_ANALOG_5CH 45 //analog RGB + WW + CW
//Digital types (data + clock / SPI) (48-63)
#define TYPE_WS2801 50
#define TYPE_APA102 51
#define TYPE_LPD8806 52
#define TYPE_P9813 53
#define TYPE_LPD6803 54
//Network types (master broadcast) (80-95)
#define TYPE_NET_DDP_RGB 80 //network DDP RGB bus (master broadcast bus)
#define TYPE_NET_E131_RGB 81 //network E131 RGB bus (master broadcast bus, unused)
#define TYPE_NET_ARTNET_RGB 82 //network ArtNet RGB bus (master broadcast bus, unused)
#define TYPE_NET_DDP_RGBW 88 //network DDP RGBW bus (master broadcast bus)
#define IS_DIGITAL(t) ((t) & 0x10) //digital are 16-31 and 48-63
#define IS_PWM(t) ((t) > 40 && (t) < 46)
#define NUM_PWM_PINS(t) ((t) - 40) //for analog PWM 41-45 only
#define IS_2PIN(t) ((t) > 47)
//Color orders
#define COL_ORDER_GRB 0 //GRB(w),defaut
#define COL_ORDER_RGB 1 //common for WS2811
#define COL_ORDER_BRG 2
#define COL_ORDER_RBG 3
#define COL_ORDER_BGR 4
#define COL_ORDER_GBR 5
#define COL_ORDER_MAX 5
//Button type
#define BTN_TYPE_NONE 0
#define BTN_TYPE_RESERVED 1
#define BTN_TYPE_PUSH 2
#define BTN_TYPE_PUSH_ACT_HIGH 3
#define BTN_TYPE_SWITCH 4
#define BTN_TYPE_PIR_SENSOR 5
#define BTN_TYPE_TOUCH 6
#define BTN_TYPE_ANALOG 7
#define BTN_TYPE_ANALOG_INVERTED 8
//Ethernet board types
#define WLED_NUM_ETH_TYPES 11
#define WLED_ETH_NONE 0
#define WLED_ETH_WT32_ETH01 1
#define WLED_ETH_ESP32_POE 2
#define WLED_ETH_WESP32 3
#define WLED_ETH_QUINLED 4
#define WLED_ETH_TWILIGHTLORD 5
#define WLED_ETH_ESP32DEUX 6
#define WLED_ETH_ESP32ETHKITVE 7
#define WLED_ETH_QUINLED_OCTA 8
#define WLED_ETH_ABCWLEDV43ETH 9
#define WLED_ETH_SERG74 10
//Hue error codes
#define HUE_ERROR_INACTIVE 0
#define HUE_ERROR_UNAUTHORIZED 1
#define HUE_ERROR_LIGHTID 3
#define HUE_ERROR_PUSHLINK 101
#define HUE_ERROR_JSON_PARSING 250
#define HUE_ERROR_TIMEOUT 251
#define HUE_ERROR_ACTIVE 255
//Segment option byte bits
#define SEG_OPTION_SELECTED 0
#define SEG_OPTION_REVERSED 1
#define SEG_OPTION_ON 2
#define SEG_OPTION_MIRROR 3 //Indicates that the effect will be mirrored within the segment
#define SEG_OPTION_FREEZE 4 //Segment contents will not be refreshed
#define SEG_OPTION_RESET 5 //Segment runtime requires reset
#define SEG_OPTION_REVERSED_Y 6
#define SEG_OPTION_MIRROR_Y 7
#define SEG_OPTION_TRANSPOSED 8
//Segment differs return byte
#define SEG_DIFFERS_BRI 0x01 // opacity
#define SEG_DIFFERS_OPT 0x02 // all segment options except: selected, reset & transitional
#define SEG_DIFFERS_COL 0x04 // colors
#define SEG_DIFFERS_FX 0x08 // effect/mode parameters
#define SEG_DIFFERS_BOUNDS 0x10 // segment start/stop bounds
#define SEG_DIFFERS_GSO 0x20 // grouping, spacing & offset
#define SEG_DIFFERS_SEL 0x80 // selected
//Playlist option byte
#define PL_OPTION_SHUFFLE 0x01
// Segment capability byte
#define SEG_CAPABILITY_RGB 0x01
#define SEG_CAPABILITY_W 0x02
#define SEG_CAPABILITY_CCT 0x04
// WLED Error modes
#define ERR_NONE 0 // All good :)
#define ERR_DENIED 1 // Permission denied
#define ERR_EEP_COMMIT 2 // Could not commit to EEPROM (wrong flash layout?) OBSOLETE
#define ERR_NOBUF 3 // JSON buffer was not released in time, request cannot be handled at this time
#define ERR_JSON 9 // JSON parsing failed (input too large?)
#define ERR_FS_BEGIN 10 // Could not init filesystem (no partition?)
#define ERR_FS_QUOTA 11 // The FS is full or the maximum file size is reached
#define ERR_FS_PLOAD 12 // It was attempted to load a preset that does not exist
#define ERR_FS_IRLOAD 13 // It was attempted to load an IR JSON cmd, but the "ir.json" file does not exist
#define ERR_FS_RMLOAD 14 // It was attempted to load an remote JSON cmd, but the "remote.json" file does not exist
#define ERR_FS_GENERAL 19 // A general unspecified filesystem error occurred
#define ERR_OVERTEMP 30 // An attached temperature sensor has measured above threshold temperature (not implemented)
#define ERR_OVERCURRENT 31 // An attached current sensor has measured a current above the threshold (not implemented)
#define ERR_UNDERVOLT 32 // An attached voltmeter has measured a voltage below the threshold (not implemented)
// Timer mode types
#define NL_MODE_SET 0 //After nightlight time elapsed, set to target brightness
#define NL_MODE_FADE 1 //Fade to target brightness gradually
#define NL_MODE_COLORFADE 2 //Fade to target brightness and secondary color gradually
#define NL_MODE_SUN 3 //Sunrise/sunset. Target brightness is set immediately, then Sunrise effect is started. Max 60 min.
// Settings sub page IDs
#define SUBPAGE_MENU 0
#define SUBPAGE_WIFI 1
#define SUBPAGE_LEDS 2
#define SUBPAGE_UI 3
#define SUBPAGE_SYNC 4
#define SUBPAGE_TIME 5
#define SUBPAGE_SEC 6
#define SUBPAGE_DMX 7
#define SUBPAGE_UM 8
#define SUBPAGE_UPDATE 9
#define SUBPAGE_2D 10
#define SUBPAGE_LOCK 251
#define SUBPAGE_PINREQ 252
#define SUBPAGE_CSS 253
#define SUBPAGE_JS 254
#define SUBPAGE_WELCOME 255
#define NTP_PACKET_SIZE 48 // size of NTP receive buffer
#define NTP_MIN_PACKET_SIZE 48 // min expected size - NTP v4 allows for "extended information" appended to the standard fields
//maximum number of rendered LEDs - this does not have to match max. physical LEDs, e.g. if there are virtual busses
#ifndef MAX_LEDS
#ifdef ESP8266
#define MAX_LEDS 1664 //can't rely on memory limit to limit this to 1600 LEDs
#else
#define MAX_LEDS 8192
#endif
#endif
#ifndef MAX_LED_MEMORY
#ifdef ESP8266
#define MAX_LED_MEMORY 4000
#else
#if defined(ARDUINO_ARCH_ESP32S2) || defined(ARDUINO_ARCH_ESP32C3)
#define MAX_LED_MEMORY 32000
#else
#define MAX_LED_MEMORY 64000
#endif
#endif
#endif
#ifndef MAX_LEDS_PER_BUS
#define MAX_LEDS_PER_BUS 2048 // may not be enough for fast LEDs (i.e. APA102)
#endif
// string temp buffer (now stored in stack locally)
#ifdef ESP8266
#define SETTINGS_STACK_BUF_SIZE 2048
#else
#define SETTINGS_STACK_BUF_SIZE 3608 // warning: quite a large value for stack
#endif
#ifdef WLED_USE_ETHERNET
#define E131_MAX_UNIVERSE_COUNT 20
#else
#ifdef ESP8266
#define E131_MAX_UNIVERSE_COUNT 9
#else
#define E131_MAX_UNIVERSE_COUNT 12
#endif
#endif
#ifndef ABL_MILLIAMPS_DEFAULT
#define ABL_MILLIAMPS_DEFAULT 850 // auto lower brightness to stay close to milliampere limit
#else
#if ABL_MILLIAMPS_DEFAULT == 0 // disable ABL
#elif ABL_MILLIAMPS_DEFAULT < 250 // make sure value is at least 250
#warning "make sure value is at least 250"
#define ABL_MILLIAMPS_DEFAULT 250
#endif
#endif
// PWM settings
#ifndef WLED_PWM_FREQ
#ifdef ESP8266
#define WLED_PWM_FREQ 880 //PWM frequency proven as good for LEDs
#else
#define WLED_PWM_FREQ 19531
#endif
#endif
#define TOUCH_THRESHOLD 32 // limit to recognize a touch, higher value means more sensitive
// Size of buffer for API JSON object (increase for more segments)
#ifdef ESP8266
#define JSON_BUFFER_SIZE 10240
#else
#define JSON_BUFFER_SIZE 24576
#endif
//#define MIN_HEAP_SIZE (8k for AsyncWebServer)
#define MIN_HEAP_SIZE 8192
// Maximum size of node map (list of other WLED instances)
#ifdef ESP8266
#define WLED_MAX_NODES 24
#else
#define WLED_MAX_NODES 150
#endif
//this is merely a default now and can be changed at runtime
#ifndef LEDPIN
#if defined(ESP8266) || (defined(ARDUINO_ARCH_ESP32) && defined(WLED_USE_PSRAM)) || defined(CONFIG_IDF_TARGET_ESP32C3) || defined(ARDUINO_ESP32_PICO)
#define LEDPIN 2 // GPIO2 (D4) on Wemos D1 mini compatible boards, and on boards where GPIO16 is not available
#else
#define LEDPIN 16 // aligns with GPIO2 (D4) on Wemos D1 mini32 compatible boards
#endif
#endif
#ifdef WLED_ENABLE_DMX
#if (LEDPIN == 2)
#undef LEDPIN
#define LEDPIN 1
#warning "Pin conflict compiling with DMX and LEDs on pin 2. The default LED pin has been changed to pin 1."
#endif
#endif
#ifndef DEFAULT_LED_COUNT
#define DEFAULT_LED_COUNT 30
#endif
#define INTERFACE_UPDATE_COOLDOWN 1000 // time in ms to wait between websockets, alexa, and MQTT updates
#define PIN_RETRY_COOLDOWN 3000 // time in ms after an incorrect attempt PIN and OTA pass will be rejected even if correct
#define PIN_TIMEOUT 900000 // time in ms after which the PIN will be required again, 15 minutes
// HW_PIN_SCL & HW_PIN_SDA are used for information in usermods settings page and usermods themselves
// which GPIO pins are actually used in a hardware layout (controller board)
#if defined(I2CSCLPIN) && !defined(HW_PIN_SCL)
#define HW_PIN_SCL I2CSCLPIN
#endif
#if defined(I2CSDAPIN) && !defined(HW_PIN_SDA)
#define HW_PIN_SDA I2CSDAPIN
#endif
// you cannot change HW I2C pins on 8266
#if defined(ESP8266) && defined(HW_PIN_SCL)
#undef HW_PIN_SCL
#endif
#if defined(ESP8266) && defined(HW_PIN_SDA)
#undef HW_PIN_SDA
#endif
// defaults for 1st I2C on ESP32 (Wire global)
#ifndef HW_PIN_SCL
#define HW_PIN_SCL SCL
#endif
#ifndef HW_PIN_SDA
#define HW_PIN_SDA SDA
#endif
// HW_PIN_SCLKSPI & HW_PIN_MOSISPI & HW_PIN_MISOSPI are used for information in usermods settings page and usermods themselves
// which GPIO pins are actually used in a hardware layout (controller board)
#if defined(SPISCLKPIN) && !defined(HW_PIN_CLOCKSPI)
#define HW_PIN_CLOCKSPI SPISCLKPIN
#endif
#if defined(SPIMOSIPIN) && !defined(HW_PIN_MOSISPI)
#define HW_PIN_MOSISPI SPIMOSIPIN
#endif
#if defined(SPIMISOPIN) && !defined(HW_PIN_MISOSPI)
#define HW_PIN_MISOSPI SPIMISOPIN
#endif
// you cannot change HW SPI pins on 8266
#if defined(ESP8266) && defined(HW_PIN_CLOCKSPI)
#undef HW_PIN_CLOCKSPI
#endif
#if defined(ESP8266) && defined(HW_PIN_DATASPI)
#undef HW_PIN_DATASPI
#endif
#if defined(ESP8266) && defined(HW_PIN_MISOSPI)
#undef HW_PIN_MISOSPI
#endif
// defaults for VSPI on ESP32 (SPI global, SPI.cpp) as HSPI is used by WLED (bus_wrapper.h)
#ifndef HW_PIN_CLOCKSPI
#define HW_PIN_CLOCKSPI SCK
#endif
#ifndef HW_PIN_DATASPI
#define HW_PIN_DATASPI MOSI
#endif
#ifndef HW_PIN_MISOSPI
#define HW_PIN_MISOSPI MISO
#endif
#endif